key features: ? 1w output power ? ultra-miniature smt case ? 3,000 vdc isolation ? 5v, 12v & 24v inputs ? -40oc to +85oc operation ? 9 standard models ? 2.0 mh mtbf minimum ? industry standard pin-out lf100di high isolation, 1w dual output smt dc/dc con vert ers series input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 reverse polarity input current 0.3 a input filter capacitor output parameter conditions min. typ. max. units output voltage accuracy 1.5 4.0 % output voltage balance balanced loads 0.1 1.0 % line regulation for vin change of 1% 1.2 1.5 % load regulation (note 1) see model selection guide ripple & noise (20 mhz) (note 2) 75 100 mv p - p ripple & noise (20 mhz) over line, load & temp. 150 mv p - p ripple & noise (20 mhz) 5 mv rms output power protection 120 % temperature coef? cient 0.01 0.02 %/oc output short circuit momentary (0.5 sec.) general parameter conditions min. typ. max. units isolation voltage 60 seconds 3,000 vdc isolation resistance 500 vdc 10 g isolation capacitance 100 khz, 1v 60 100 pf switching frequency 50 100 150 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 oc operating temperature range case -40 +90 oc storage temperature range -40 +125 oc cooling free air convection humidity rh, non-condensing 95 % physical case size 0.60 x 0.31 x 0.26 inches (15.24 x 8.0 x 6.7 mm) case material molded black plastic (ul94-v0) weight 0.07 oz (2.2g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25oc, gnd benign 2.0 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 12 vdc input -0.7 18.0 24 vdc input -0.7 30.0 lead temperature 1.5 mm from case for 10 sec. 300 oc internal power dissipation all models 550 mw caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com electrical speci? cations speci? cations typical @ +25c, nominal input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice. rohs compliant
model selection guide mechanical dimensions notes: 1. load regulation is measured for an output change of 20% to 100%. 2. when measuring output ripple, it is recommended that an external 0.33 f ceramic capacitor be placed from the +vout pin to the -vout pin. for noise sensitive applications, the use of 0.47 f capacitors will reduce the output ripple. 3. operation at no-load will not damage these units. however, they may not meet all speci? cations. 4. the converter should be connected to a low ac-impedance source. an input source with a highly inductive impedance may affect the stability of the converter. in applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. in this case, it is recommended that a low esr (esr <1.0 at 100 khz) capacitor be mounted close to the converter. for 5v input units a 2.2 f is recommended, for 12v input units, a 1.0 f, and for 24v input units, a 0.47 f. 5. dual output units may be connected to provide a 10 vdc, 24 vdc or 30 vdc output. to do this, connect the load across the positive (+vout) and negative (-vout) outputs and ? oat the output common. 6. it is recommended that a fuse be used on the input of a power supply for protection. see the table above for the correct rating. model number input output load regulation (%, max) ef? ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load lf101di 5 4.5 - 5.5 277 30 5.0 100.0 2.0 10 72 500 lf102di 5 4.5 - 5.5 255 30 12.0 42.0 0.8 7 78 500 lf103di 5 4.5 - 5.5 258 30 15.0 34.0 0.7 7 79 500 lf111di 12 10.8 - 13.2 112 12 5.0 100.0 2.0 8 74 200 lf112di 12 10.8 - 13.2 105 12 12.0 42.0 0.8 5 80 200 lf113di 12 10.8 - 13.2 104 12 15.0 34.0 0.7 5 81 200 lf121di 24 21.6 - 26.4 57 7 5.0 100.0 2.0 8 72 100 LF122DI 24 21.6 - 26.4 53 7 12.0 42.0 0.8 5 79 100 lf123di 24 21.6 - 26.4 53 7 15.0 34.0 0.7 5 80 100 pin description pin description 1-vin 7 na 2 +vin 8 +vout 3na 10na 5 common 11 na 6 -vout 12 na na = not available for connection pin connections 5v out f max 12 & 15v out f max 10 2.2 capacitive load board layout derating curve micropower direct www.micropowerdirect.com 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com notes: ? all dimensions are typical in inches (mm) ? tolerance: inches x.xx = 0.01 millimeters x.x = 0.25 x.xx = 0.13 pin: 0.002 ( 0.05) ? pin 1 is marked by a ?dot? or indentation on the unit. the curved edge of the case indicates the pin 1 side.
|
